马来西亚彭亨大学出版社
期刊
会议
图书
作者:E. N. Krishnan , N. Balasundaran , R. J. Thomas
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:The main concerns in energy from petroleum-based fuels are the scarcity, cost, and pollution the fuels. Now, natural gas is considered as a better alternative. The process of converting natural gas into liquefied natural gas (LNG) is highly energy intensive and consumes abou...
作者:Sathyashankara Sharma , Achutha kini , Gowri Shankar ...
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:Presence of various amount of B4C reinforcement (2, 4 & 6% wt.) in Al6061 alloy on the hardness and tensile behaviour is studied in the present work. The influence of artificial aging due to presence of reinforcement on Al6061 alloy also evaluated. Brinell hardness and failu...
作者:I. Kustiningsih , Sutinah , M. Stefirizky ...
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:Effects of sonication and hydrothermal treatment time on TiO2 nanowires (TNWs) formation have been investigated. Sonication of TiO2 P25 sol was performed using sonicator water bath Cole for 0.5, 1 and 2 hours followed by hydrothermal treatment. The hydrothermal treatment was...
作者:B. Mallick , B.R. Sarkar , B. Doloi ...
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:Electro chemical discharge hybrid machining process involves in micro-machining to cut microchannel, micro-profile as well as micro-slot, blind hole on hard materials like ceramic, quartz and glass. Experimentation has been performed using an indigenously developed micro-ECDM set...
作者:Sangmesh B , Gopalakrishna K. , Manjunath S.H. ...
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:LEDs, of late, have received attention as the next generation lighting system for enhanced luminous efficiency and higher lifespan. However, the thermal management of the LEDs is the crucial parameter to be countered for global acceptance as a revolutionary illumination sour...
作者:K. A. M. Said , R.L. Jamai1 , N.S. M. Sutan ...
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:Enhancing membrane permeation is usually an important parameter in the membrane development for filtration. In this study, polysulfone membrane equipped with different concentration of silver nitrate (0.5-2.0 wt%) were fabricated by phase inversion and later be known as composite...
作者:Y. Menni , A. Azzi , A. J. Chamkha
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:This manuscript presents a numerical analysis of fluid flow and heat transfer in rectangular cross section channels with and without baffles using air as the working fluid at Reynolds numbers ranging from 12,000 to 32,000. Four various channel geometries were studied in this anal...
作者:Triwiyanto , O. Wahyunggoro , H. A. Nugroho ...
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:Muscle fatigue is a major problem in the study based on electromyography (EMG) signal. When the muscle in the fatigue condition, the power of the EMG signal increases significantly. This phenomenon can be a problem in the elbow-joint angle estimation. The purpose of this study is...
作者:N. T. Alshabatat
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:This paper presents a method for improving the buckling capacity of slender columns by employing functionally graded materials (FGMs) instead of isotropic materials in constructing these members. The volume fractions of FGM constituents are varied along the column length by a tri...
作者:Nagraj Patil , Gopalakrishna K , Sangmesh B ...
来源:[J].Journal of Mechanical Engineering and Sciences (JMES), 2018, Vol.12 (3)UMPP
摘要:This paper attempts to compare and contrast cryogenic treated and untreated carbide cutting tool in turning operation of AISI304 steel. Machining parameters, namely cutting speed, feed rate and depth of cut are optimized for cryogenic treated tools. Tool life of the insert was de...

我们正在为您处理中,这可能需要一些时间,请稍等。

资源合作:cnki.scholar@cnki.net, +86-10-82896619   意见反馈:scholar@cnki.net

×