全部文献期刊会议图书|学者科研项目
中外文文献  中文文献  外文文献
作者:S. Chavan , A. Pawar , S. Talbar
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:This paper presents a novel approach to multimodality medical image fusion for better visualization of lesions and calcification. The algorithm utilizes source modalities as Computed Tomography (CT) and Magnetic Res-onance Imaging (MRI). It is a feature based fusion technique in ...
作者:Adnan Shaikh , Nilaj Deshmukh
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:In any combustion process of a fuel there will be always some unburned carbon (soot) generated and some ash carried with the stack gas stream. Soot, ash, and molten ash (slag) will accumulate at the tube banks of the heat exchangers. Some ash will even melt down at the tube surfa...
作者:Ganesh Dongre , Javed Shaikh , Leena Dhakad ...
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:The fundamental machining techniques were established long back. However, machining operations consume a large amount of money annually worldwide. Advanced engineering materials, such as ceramics, MMC, Titanium (Ti), Inconel and its alloys offer properties like high strength...
作者:R. Mangalekar , C. Ramdas , B. Dawari
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:Analysis of double strap bolted lap joint was carried out using Finite Element Method (FEM). Angle of interfacial pressure distribution between the plates to be joined using preloaded bolted connection has been a debatable point though widely researched. Shigale's Pressure c...
作者:Ashish Rajak , Sachin Kore
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:Hemming is a metal sheet forming procedure to obtain tight fit or minimum gap when folding of sheet edges takes place over another. Bending of sheet metal edges takes place to 1800 in the last step of production line. This process is assumed to be a critical as it affects the sur...
作者:S. Saste , A. Sawant
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:Speed of the arithmetic operations often depends upon formation and propagation of carry. With the binary number system, the speed of arithmetic operations such as addition and subtraction is limited by formation and propagation of carry especially as the number of bits increases...
作者:S. More , P. Choudhari
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:Photo plethysmography (PPG) is used to estimate the blood flow using light. Researchers from different domains of science have been working with PPG because of its advantages as non-invasive, inexpensive, and convenient diagnostic tool. Traditionally, it has been used to measure ...
作者:Getu Areda , Sachin Kore
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:Numerical modeling and simulation of an electromagnetic crimping process will give us better insight how different phenomenon relate and affect the result of deformation significantly. This paper focuses on modeling and simulating of electromagnetic crimping of Al6016-T6 tube on ...
作者:S. Bansod , A. Nandedkar
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:Anomalies in video scenes means unexpected or unusual activity which is usually not frequently observed. Such activities hence are rare and require sudden attention so that it can be detected as early as possible. There is a need to automatically identify and locate where such an...
作者:Ketan Jagtap , Raju Pawade
来源:[C].Proceedings of the International Conference on Communication and Signal Processing 2016 (ICCASP 2016)2016
摘要:Decisive requirement for the long-term stability of the artificial joint is to minimize the release of debris particles. The wear/debris induced osteolysis and aseptic loosening are the result of failure of metal-on-metal joint implants. Severe plastic deformation (SPD) processes...

我们正在为您处理中,这可能需要一些时间,请稍等。

资源合作:cnki.scholar@cnki.net, +86-10-82896619   意见反馈:scholar@cnki.net

×