| 作者：Wenlong Lu , Qunfen Qi ... |
| 来源：[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (5-8), pp.2121-2137Springer |
| 摘要：Representing the semantics of the interaction of two or more tolerances (i.e., composite tolerance) explicitly to make them computer-understandable is currently a challenging task in computer-aided tolerancing (CAT). We have proposed a description logic (DL) ontology-based approa... |
全文获取| 作者：... Yuchun Huang , Liping Zhou , Wenlong Lu |
| 来源：[J].Acta Metallurgica Sinica (English Letters)(IF 0.467), 2017, Vol.30 (6), pp.576-584Springer |
| 摘要：This study reports that small amounts of MoO3 multilayer ribbon crystal (MoO3 MLRC) in Ni3Al intermetallics showed the decreased friction coefficients and improved wear resistance at different contact loads. Specifically, the friction coeffic... |
| 作者：Wenlong Lu , Jamal Nasar ... |
| 来源：[J].Bulletin of Environmental Contamination and Toxicology(IF 1.105), 2019, Vol.103 (6), pp.854-859Springer |
| 摘要：Abstract(#br)A hydroponic experiment was carried out to study the accumulation characteristics of copper (Cu) and lead (Pb) combined pollution in three ornamental plants. The results showed that these tested ornamental plants had higher tolerance to Cu–Pb combined pollution ... |
| 作者：Wenlong Lu , Po Zhang ... |
| 来源：[J].Tribology International(IF 1.536), 2017Elsevier |
| 摘要：Abstract(#br)Influence of surface topography on torsional fretting under flat-on-flat contact were investigated. Contact surfaces of the lower specimens were prepared by milling with different initial surface roughness while the upper specimens were polished. Results indicate tha... |
| 作者：... Junpeng Shi , Zhaojian Zhang , Wenlong Lu |
| 来源：[J].Signal Processing(IF 1.851), 2019, Vol.164, pp.151-162Elsevier |
| 摘要：Abstract(#br)In this paper, we propose a space-time allocation strategy for collocated multiple-input multiple-output (MIMO) radar to determine the beam directions to multiple targets, to be tracked. The transmit beams are allocated to different targets with distinct time units i... |
| 作者：Wenlong Lu , Zili Lei ... |
| 来源：[J].Precision Engineering(IF 1.393), 2019Elsevier |
| 摘要：Abstract(#br)Atomic force microscope (AFM) is widely applied to the measurement of the micro-nano structures due to its three-dimensional spatial resolution of sub-nanometer. However, the height measurement traceability in the z-axis is complex to be implemented in conventional A... |
| 作者：... Bin Liu , Wenlong Lu , Yabin Zhang |
| 来源：[J].Optics and Lasers in Engineering(IF 1.916), 2019Elsevier |
| 摘要：Abstract(#br)Divided-aperture (DA) microscopy is an imaging method that, in addition, improves the anti-scattering capability. The present state-of-the-art imaging methods have the drawbacks of requirement of scanning or low spatial resolution. In this paper, we propose a DA digi... |
| 作者：... Yuchun Huang , Liping Zhou , Wenlong Lu |
| 来源：[J].Composites Part B(IF 2.143), 2017, Vol.108, pp.354-363Elsevier |
| 摘要：Abstract(#br)A dislocation-density-based model is selected to investigate the mechanisms of the improvement in the mechanical and tribological performance of the tribo-layer during sliding friction. Ni 3 Al matrix composites are used for validating the analysis model. The experim... |
| 作者：Wenlong Lu , Qunfen Qi ... |
| 来源：[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2018, Vol.97 (5-8), pp.1801-1821Springer |
| 摘要：Abstract(#br)In this paper, a tolerance representation model for generating tolerance specification schemes and corresponding tolerance zones is proposed to meet the requirement of the representation of tolerance information semantics. This model is hierarchically organized and c... |
| 作者：Wenlong Lu , Gengpei Zhang ... |
| 来源：[J].Tribology Transactions(IF 0.914), 2014, Vol.57 (3), pp.553-560Taylor & Francis |
| 摘要：Running in is a complex process, and it significantly influences the performance and service life of wear components as the initial phase of the entire wear process. Surface topography is an important feature of wear components. Therefore, it is reasonable to investigate the runn... |