全部文献期刊会议图书|学者科研项目
中外文文献  中文文献  外文文献
作者:Kuo-Hsun Lee , Sen-Yeu Yang , Ji-Gang Yang
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (1-4), pp.753-761
摘要:... In this research, the prevalent alloy Ti-6Al-4V was used to investigate the optimization process parameters of heat treatment by using the Taguchi method. Hardness after aging and tensile strength (TS) were chosen as quality characteristics. Eight controllable factors were...
作者:Min Zhou , Lingpan Kong , Liangxi Xie ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (9-12), pp.3543-3553
摘要:... To address the non-uniformity issues of the existing mortar nozzles, we investigate the effects of a special nozzle structure on its outlet velocity uniformity by using Taguchi methods and the finite volume method. The experimental studies are conducted under various combinat...
作者:Xizhao Wang , Jun Duan , Ming Jiang ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.93 (5-8), pp.2963-2974
摘要:... A method named laser ablation by projective galvanometer scanning (LPAGS) can effectively apply laser ablation technology to three-dimensional processing field. For three-dimensional processing, the machining results are strongly affected by the processing parameters. Optimal...
作者:Haijun Mao , Li Jiao , Shoufeng Gao ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.91 (1-4), pp.657-665
摘要:This paper presents a study of the Taguchi application to optimize surface quality based on fractal theory in meso-scale end-milling operation. Usually, the surface quality is characterized by roughness, but in the meso-scale area, the size of the workpiece will be difficult to m...
作者:Hakan Terzioğlu
来源:[J].Measurement(IF 1.13), 2020, Vol.149
摘要:... Taguchi method was used to determine the performance effects in the most accurate way. Taguchi method used three levels with three factors: material (copper, aluminum and brass), engine speed (I, II and III) and water pressure (1-2.5-3.5 bar). In addition, in the Taguchi method...
作者:Renata Orłowska , Katarzyna A. Pachota , Joanna Machczyńska ...
来源:[J].Electronic Journal of Biotechnology(IF 0.827), 2020, Vol.43, pp.8-15
摘要:... Camus 1927) using the Taguchi method. We evaluated uniform donor plants under varying experimental conditions of in vitro anther culture using the Taguchi approach, and verified the optimized conditions.(#br)Results(#br)Optimization of the regeneration conditions resulted i...
作者:Vezir Ayhan , Çiçek Çangal , İdris Cesur ...
来源:[J].Fuel(IF 3.357), 2020, Vol.261
摘要:... In this study, using different proportions of corn oil methyl ester (COME) blends (B0, B10, B20 and B50) and EGR (EGR0, EGR10, EGR15 and EGR20) on a direct injection (DI) diesel engine at variable loads (40%, 60%, 80% and 100%) and speed (1600 and 2400 rpm) conditions, the optimum factor levels in terms of performance and emission characteristics were determined by Taguchi method...
作者:Mohammad R. Ahmadi Balootaki , Rahim Zamanian , Parviz Ghadimi
来源:[J].Journal of the Brazilian Society of Mechanical Sciences and Engineering(IF 0.234), 2017, Vol.39 (4), pp.1151-1164
摘要:... Initially, five parameters are analyzed on three levels and 27 tests are designed applying Taguchi’s method. After 27 tests, optimal values of the designated parameters are found for the sound source located at the center. To obtain more accurate values, the parameters ar...
作者:B.Y. Sun , J.B. Xiao , Z.B. Li ...
来源:[J].Catena(IF 1.881), 2018, Vol.162, pp.100-107
摘要:... In order to elucidate the effects of slope, flow discharge and freeze-thaw factors on SDC, the indoor artificial freezing-thawing method was applied in combination with scour to simulate the soil detachment process. Signal-to-noise (S/N) ratio analysis was also used to e...
作者:Timur Canel , Muzaffer Zeren , Tamer Sınmazçelik
来源:[J].Optics and Laser Technology(IF 1.365), 2019, Vol.120
摘要:...(#br)In the confirmation experiment with the proposed parameters by Taguchi method, minimum Crack Length was obtained as 208.56 (μm/mm 2 ), minimum Surface Porosity was obtained as 0.024%, the best surface Roughness was obtained as 28.29 μm, minimum defect depth was obtai...

我们正在为您处理中,这可能需要一些时间,请稍等。

资源合作:cnki.scholar@cnki.net, +86-10-82896619   意见反馈:scholar@cnki.net

×