全部文献期刊会议图书|学者科研项目
中外文文献  中文文献  外文文献
作者:You-Qun Zhao , Hai-Qing Li , Fen Lin ...
来源:[J].Chinese Journal of Mechanical Engineering(IF 0.263), 2017, Vol.30 (4), pp.982-990
摘要:The accurate estimation of road friction coefficient in the active safety control system has become increasingly prominent. Most previous studies on road friction estimation have only used vehicle longitudinal or lateral dynamics and often ignored the load transfer, which tends t...
作者:Seyed Ali Niknam
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.91 (1-4), pp.1079-1089
摘要:..., geometry and coating) as well as friction on the thickness of exit up milling side burr is therefore required to decrease the incidence of burr formation. Although friction angle λ has a direct proportion to negative shear angle ϕ as well as radial and tangential cutting ...
作者:Da-Wei Zhang , Min-Chao Cui , Miao Cao ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.91 (9-12), pp.3823-3831
摘要:The incremental ring compression test (IRCT) was developed to investigate the friction condition in cold-rolling process of spline or thread shaft. During IRCT process, the upper die is loaded intermittently and new oil film between ring and dies will appear, which can reflect th...
作者:Arash Fattah-alhosseini , Mojtaba Vakili-Azghandi , Meysam Haghshenas
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (1-4), pp.991-1002
摘要:The effects of local sever plastic deformation through multi-pass friction stir processing on the passive and electrochemical response of pure Ti are studied in a borate buffer solution (pH = 7) in the present paper. Microstructures of treated and untreated samples were characte...
作者:Takeshi Yoneyama
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (5-8), pp.2251-2261
摘要:A friction sensor that can detect both pressure and frictional stress on the tool’s surface during hot forging has been developed. The detection principle was introduced in 2004 by the present author; however, a sensor suitable to be installed in the forging die has not been...
作者:Hakan Kalkan , Tugce Hacaloglu , Bilgin Kaftanoglu
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.92 (9-12), pp.3311-3318
摘要:Investigation of friction is carried out in the radial drawing region between the die and blank holder and also in the stretching zone over the punch in deep drawing. Two methods are developed to calculate the coefficient of friction in each zone using the experimentally determin...
作者:P.-C. Lin , S.-M. Lo
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.92 (5-8), pp.2425-2437
摘要:... Therefore, friction stir clinching (FSC), a variant of friction stir spot welding (FSSW), was developed for joining alclad AA2024-T3 sheets. In this study, a FSC tool with a flat shoulder and a smooth probe, and a FSC die with a grooved circular cavity were used to make joint...
作者:Vahid Farajkhah , Yi Liu
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (1-4), pp.339-348
摘要:Effects of clamping area and welding speed on the development of residual stress fields in aluminum plates joined by the friction stir welding process were investigated in this paper. Friction stir welding on two aluminum alloy 6061-T6 plates was simulated in a three-dimensional,...
作者:Weideng Wang , Dean Deng , Zhitao Mao ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.88 (5-8), pp.2191-2200
摘要:The influence of tool rotation rates on temperature profiles, microstructure, and mechanical properties of friction stir welded AZ31 magnesium alloys was investigated experimentally and numerically. AZ31 plates with a thickness of 8 mm were joined by friction stir welding proces...
作者:Ahmed Z. Naser , Basil M. Darras
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.91 (1-4), pp.781-790
摘要:Friction stir processing has recently emerged as an effective alternative method for fabricating metal matrix composites. This paper presents an experimental investigation on the feasibility of using friction stir processing for fabricating Mg/SiC surface composites. The effects ...

我们正在为您处理中,这可能需要一些时间,请稍等。

资源合作:cnki.scholar@cnki.net, +86-10-82896619   意见反馈:scholar@cnki.net

×