全部文献期刊会议图书|学者科研项目
中外文文献  中文文献  外文文献
作者:Dong Ren , Yueju Liu , Xianchao Zhang ...
来源:[J].Journal of Orthopaedic Surgery and Research(IF 1.013), 2017, Vol.12 (1)
摘要:A three-dimensional finite element model (FEM) of the knee joint was established to analyze the biomechanical functions of the superficial and deep medial collateral ligaments (MCLs) of knee joints and to investigate the treatment of the knee medial collateral ligament injury.
作者:S. Peirovi , M. Pourasghar , A. Farokhi Nejad ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.93 (1-4), pp.1399-1413
摘要:The effectiveness of finite element simulation techniques for laser cutting of 1.2-mm-thick aluminium sheets has been studied. Lagrangian and Arbitrary Lagrangian-Eulerian techniques were used to model and simulate laser cutting process. The reliability of finite element results ...
作者:Samad Nadimi Bavil Oliaei , Yiğit Karpat
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (1-4), pp.819-829
摘要:... A method of including BUE formation in finite element simulations is to use sticking friction conditions at the tip of the tool. However, this approach is shown to be insufficient to simulate BUE formation in microscale machining. Therefore, the cutting edge is modified with ...
作者:Jabbar Gattmah , Fahrettin Ozturk , Sadettin Orhan
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.93 (1-4), pp.1229-1241
摘要:... Therefore, an accurate finite element model is extremely important to improve part quality and reduce the cost of the part. In this article, a cold tube drawing with a fixed straight mandrel is studied experimentally and numerically for AISI 1010 steel tube. Two different red...
作者:Xingzong Liu , Chun’an Tang , Lianchong Li ...
来源:[J].Rock Mechanics and Rock Engineering(IF 1.16), 2017, Vol.50 (7), pp.1901-1917
摘要:... This paper describes the microseismic monitoring technology, and three-dimensional (3D) finite element analysis is used to explore the microseismic activities and damage mechanisms in the right bank slope during reservoir impounding. Based on data obtained from microseismic m...
作者:Mohanad Alabdullah , Ashwin Polishetty , Junior Nomani ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.91 (1-4), pp.501-516
摘要:This paper presents a finite element cutting model based on physical microstructure to investigate the thermo-mechanical behaviour of AL-6XN Super Austenitic Stainless Steel in the primary shear zone. Frozen chip root samples were created under dry turning operation to observe th...
作者:Min-Chao Cui , Sheng-Dun Zhao , Da-Wei Zhang ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (9-12), pp.2477-2490
摘要:... In order to improve the accuracy of finite element simulation, the plastic flow behavior and constitutive characteristic of 42CrMo steel during warm forming process are studied through the isothermal warm compression tests, and then, the microstructure of tempered sorbite an...
作者:Chaohua Wu , Zhengfeng Jiang , Wei Fan ...
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (1-4), pp.241-248
摘要:...0 to make finite element analysis for multi-wire saw silicon rods with consolidated abrasive diamonds by loading different process parameters, including wire-line speed and feeding force. Meanwhile, according to removing mechanism of brittle materials, when the maximum cutting...
作者:Pavel Karban , Ivo Doležel
来源:[J].Electrical Engineering(IF 0.303), 2017, Vol.99 (4), pp.1255-1261
摘要:An alternative fully adaptive finite element approach is used for modeling fast transient phenomena on overhead lines. The methodology is based on rewriting the hyperbolic transmission equation for voltage to two specific equations where one unknown is the voltage itself and anot...
作者:Konstantinos Salonitis , Dimitrios Chantzis , Vassilios Kappatos
来源:[J].The International Journal of Advanced Manufacturing Technology(IF 1.205), 2017, Vol.90 (9-12), pp.2689-2701
摘要:... This paper presents a novel user-friendly method for the design optimization of lattice components towards weight minimization, which combines finite element analysis and evolutionary computation. The proposed method utilizes the cell homogenization technique in order to redu...

我们正在为您处理中,这可能需要一些时间,请稍等。

资源合作:cnki.scholar@cnki.net, +86-10-82896619   意见反馈:scholar@cnki.net

×